AVE Video Serial Synchronous ATM Interface VSSI-PRO Manuel d'utilisateur Page 97
- Page / 138
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
ADPRO FastTx by Xtralis Installation and User Manual
Doc 11949_06 85
The Quad option captures three alarm images in a user-defined period (defined under Camera
Settings/General tab) and displays the images at ADPRO VideoCentral, along with a fourth
pane which sequences through the three images to highlight movement.
4.3.15 Control Outputs
The Control Outputs option defines a number of parameters about the type and operation of the
output circuits connected to the ADPRO FastTx. The outputs are ‘open collector’ transistor
circuits used to generate a control signal (upon activation of an alarm) to activate third-party
equipment at the remote site, for example a boom gate controller or a floodlight control device.
Select the control output number from the displayed list. The number of control outputs available
depends on the ADPRO FastTx Model number. The status of a control output is shown by a
small icon to the left of the channel number.
• A control output is free when the ‘empty’ icon is shown next to the number
•The Connect button is used to enable a control output. A green tick is shown and details
can be modified
• To temporarily disable the use of a control output, the Disconnect button is used and a red
cross is shown. For example, set Disconnect if maintenance is being performed on the unit
under control.
Figure 85: Control Output Settings Menu
- ADPRO FastTx by 1
- Installation and 1
- User Manual 1
- Compliance of Power Cord 5
- Connection to Other Equipment 5
- Contact Us 5
- Declaration of Conformity 6
- Contents 7
- List of Figures 9
- Doc. 11949_06 10
- List of Tables 12
- 1 Introduction 13
- Monitoring 14
- 2.1 Physical Location 15
- Instructions 16
- 2.3.2 Static Discharge 17
- 2.3.3 Grounding Requirements 17
- 2.5 Mounting the ADPRO FastTx 19
- 2.7 Setting up the PC 20
- Doc 11949_06 9 21
- Doc 11949_06 11 23
- Doc 11949_06 13 25
- Null-modem Cable Wiring 27
- Doc 11949_06 17 29
- Doc 11949_06 19 31
- Doc 11949_06 21 33
- 2.10 Adding a New Site 35
- 2.12.2 Front Panel LED 37
- 2.14 Firewall Configuration 38
- 3 ADPRO FastTx Connectors 39
- 3.1 Power Connection 40
- Doc 11949_06 29 41
- 3.2.2 COMMS 2 42
- 3.3 Audio 43
- 3.3.1 Audio Switch Port 44
- 3.3.3 Audio Configuration 45
- 1 2 3 45678 9 46
- 3.3.4 Zoned Audio 47
- 3.4 Video Input Connections 48
- 3.5 Video Output 49
- 3.6 Configuration Switches 50
- 3.7 Alarm Inputs 51
- Doc 11949_06 41 53
- 3.8 Control Outputs 54
- 3.9 PTZ Connection 55
- 44 Doc 11949_06 56
- 3.9.1 PTZ Port Setup 57
- 3.11 Data Connection 59
- 3.12.4 Push to Talk - Pin 7 60
- 3.12.6 Fault Relay 61
- 4 Programming ADPRO FastTx 63
- Doc 11949_06 53 65
- 4.3.3 Site Details 67
- 4.3.4 Date/Time Settings 68
- 4.3.5 Licensing 69
- 4.3.6 Communications 70
- Ethernet Properties 71
- Subnet Mask 72
- Default Gateway 72
- Video Data Rate 73
- Modem/TA Model 74
- Line Type 74
- Data Rate 75
- Dial Time 75
- Answer Rings 75
- Initialisation String 75
- Redcare Setting 75
- Doc 11949_06 65 77
- Base Port Number 78
- Connection Timeout 78
- Enable WAN Optimisation 78
- 4.3.7 Call List 79
- Main Communications Link 80
- 4.3.8 Connected Equipment 81
- General Alarm Relay Settings 82
- PTZ Settings 82
- 4.3.9 Cameras 83
- Camera Settings 84
- Doc 11949_06 75 87
- Activity Detection Tab 88
- Contrast Monitoring Tab 89
- 4.3.10 Monitor 90
- 4.3.11 Transaction Devices 90
- 4.3.12 Transparent Data Port 91
- Baud Rate 92
- Data Bits 92
- Stop Bits 92
- Flow Control 92
- 4.3.13 Alarm Inputs 93
- Alarm Input Type 94
- Hold Time 94
- 4.3.14 Presidium Inputs 95
- Presidium Input Settings 96
- 4.3.15 Control Outputs 97
- 4.3.16 Audio 98
- Audio General Properties 99
- 4.3.17 Arming / Disarming 100
- Indicate Active Sensor 101
- 4.3.18 Operational Behaviour 102
- 4.3.19 Operational Modes 102
- Mode Selection 103
- Mode Name 103
- Doc 11949_06 104
- 4.3.20 Camera Behaviour 105
- Alarm Logic 106
- Event Inputs 106
- Doc 11949_06 95 107
- Event Response 108
- Dial Out on Event 109
- Dial Out on Video Loss 109
- Dial Out on Invalid Contrast 109
- Guard Tour Settings 110
- Doc 11949_06 99 111
- Doc 11949_06 101 113
- 4.3.22 Entry/Exit Behaviour 114
- Doc 11949_06 103 115
- Exit Path and Delay 116
- 4.3.23 Maintenance 117
- Zone Isolate 118
- SitePulse 119
- 5 Event Log 121
- Doc 11949_06 111 123
- 112 Doc 11949_06 124
- Doc 11949_06 113 125
- 114 Doc 11949_06 126
- Doc. 11949_03 115 127
- 116 Doc. 11949_03 128
- Doc 11949_06 117 129
- 7.1 Software Upgrade Process 131
- 8 Specifications 133
- 122 Doc 11949_06 134
- Doc 11949_06 123 135
- 124 Doc 11949_06 136
- Te le me t ry 136
- Doc 11949_06 125 137
- 126 Doc. 11949_05 138
Produits connexes et manuels pour Mise en réseau AVE Video Serial Synchronous ATM Interface VSSI-PRO
(48 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels